Search

7 Jun 2010: All the test points, hysteresis data and determined fatigue characteristic values have been collected in a database. ... Fig. 10: Influence of direction of test specimens on the cyclic material behaviour of steel H260B.

7 Jun 2010: heavily. Generally, inputs such as chromium, carbon, sulphur, phosphorus and test temperature were. ... of hidden units involved increase. This is consistent with expectation. The test error.

7 Jun 2010: CFI tests were performed with strain-hold of 10 minutes at tensile peak strain as the same temperature with LCF test. ... P122,HAZ. P92,HAZ. Test temp : 700oC Continuous cycle Base HAZ Weld P92 P122.

11 Oct 2010: concentration. The authors present here the first spot welding tests on the novel alloy. ... a shear tensile test samples; b cross-tensile test samples1 Spot weld specimen geometries (dimensions in mm).

7 Jun 2010: in the ‘70) resulted in correlations established between fracture appearance in small-scale test pieces and fracture parameters measured in full-scale tests. ... Figure 6 – Crack arrestor modelling and actual test results on X100 pipes [25].

7 Jun 2010: Tensile and hardness tests were carried out to measure the strength level of the microstructures produced. ... The results of constant loading tests with pre-charged specimens are shown in Fig.

7 Jun 2010: A finite element model of the Jominy end-quench test is constructed asshown in Fig. ... How could the analysis be refined? (iii) Explain which (if any) of the various solutions might be appropriatefor: (a) estimating the number of tests which could be

7 Jun 2010: Figure 7 – Hardness test pattern. Tensile tests were carried out both in transversal (or cross weld, CW) and longitudinal (or all weld AW) direction. ... Note: specimen broken in parent metal. 3.3 BEND TESTS According to ISO 5173, side bend test

7 Jun 2010: The length changes should not be transmitted through a second material upon whoseexpansion coefficient depends the evaluation of the test material. ... High–speed dilatometers generally do not have long term electronic or mechanical stability.Equipment

7 Jun 2010: To initiate the GA search, the inputs are randomly generated and placed innorm_test.in. ... 18 Heat treatment temperature / K 1279 1473. 19 Test temperature / K 293 1273.

7 Jun 2010: together with a few longitudinal tests on seam weldedpipe sections subjected to internal pressure.4 In the lattercase the highest principal stress is transverse to thewelding direction and the test is ... In a cross-weld test the sample fails in either

7 Jun 2010: The trained models weresubjected to a variety of metallurgical tests. As expected, the test temperature (in the range25–1100 C) was found to be the most significant variable influencing the tensile ... To avoid this difficulty, the experimental data

7 Jun 2010: process. However, it is first necessary to conduct test simulations to discover the. ... Figure 9.5 - Results of test simulation with 2, 4 and 8 populations.

7 Jun 2010: 4). Tests performed in Hong Kong have confirmed the safe behaviour of HISTAR bearing piles during installation with heavy diesel and hydraulic impact hammers as well as during static test loadings ... Full-scale tests performed with S460 quality [22] as

7 Jun 2010: Charpy V Notch Charpy V Notch impact test impact test. (CVN)(CVN). ... SMAW FCAW SAWE= 12kJ/cm E= 8 kJ/cm E= 35 kJ/cm. Bent test after welding : A913/gr.

7 Jun 2010: 10.13. Sheet2. Sheet3. Fatigue Performance. Test 1. Test 2. Conditions. 30% 10%. ... Six Strand Wire Rope. 166,878. 316,418. Two tests completed – the first test was actually stopped prior to failure of the whole sample although a large proportion of

7 Jun 2010: The fatigue limit (obtained by HCF test) was slightly higher in welded normalized steel than in welded TMCP steel. ... Vickers hardness test was made under a 300 g load along a line crossing base metal, HAZ and weld metal.

7 Jun 2010: For steel E911 the creep tests performed during COST 501 Program were collated by ECCC in 2000. ... Several very long creep tests are included in the database: seven creep data passed 100,000 hours; the longest broken creep test reached 113,431 hours at

7 Jun 2010: The hydrogen embrittlement susceptibility of the steels was evaluated by means of a constant loading test, a slow strain rate test and a hydrogen immersion test. ... For the CLT, the constant load was applied to samples with a conventional creep test

7 Jun 2010: The delaminations lead to a decrease in triaxiality of the stress state in the impact test samples. ... Impact tests were conducted in a temperature range from 103 to 423 K.