Search

18 Feb 2002: Theexperimental results presented in this reference are avery valuable benchmark against which to test new so-lutions. ... Comparison with Sewall’s Experiment. The third test case was based on one of the tests re-ported in Ref.

4 Aug 2010: 35]. Morelong term corrosion tests are needed to establish relationshipsbetween corrosion rates and environmental properties. ... 2] I. Balafas, 2003. Fibre-reinforced-polymers vs steel in concrete bridges: structuraldesign and economic viability.

29 Mar 2004: The tests were done with a cross-head speed of5 mm/min, and were recorded with a Sony DCR-PC110E digital video camera. ... Displacement (mm). Fo. rce. (N. ). Test. Abaqus. 6. Fig. 17 Response to vertical tip loads.

15 May 2014: integrated models of GSHP systems and to test these models with case studies of existing GSHP. ... incorporating this uncertainty in the design and economic evaluation of full-size (i.e.

23 Feb 2006: All test results presented in this section were obtained on 380 mm widemembranes with a height, between the supports, of 128 mm. ... Laser scanning frame. 3.2. Shear test apparatus. 3.3. Square membrane apparatus.

30 Jul 2007: After each test, photographs were taken of everyfracture surface. The fracture plane was seen to intersect oneor more tensiometers in 7 out of 17 tests. ... This. Table 2. Test programme. Type of four-pointbending test. Test Initial suctionmeasured, s9i:

12 Jul 2002: To cross-head. To baseof Instron. Figure 5.2: Kxx test set-up. Prediction of Rolamite Stiffness. ... ess. N/m. m2. E=13200. Figure 5.10: Stiffness test on coated wire used in hinge.

27 Aug 2002: Simple equilibrium considerations lead torelationships between the tension in the middle of cord i, Ti, the sag of cord i, si, and the sag of cord i 1,si1, etc. ... This was probably due to the damage mentioned above. This test confirmed a conclusion

20 Mar 2000: Fig. 1: Bonded plates on test beams. 2 Reports Structural Engineering International 4 / 99. ... time.Similarly, the use of GFRP compositesfor complete structures is proving tobe economic when there are access dif-ficulties for building conventionalheavy

22 Aug 2001: 2.2 Some remarks about calibration chamber tests. 3 Centrifuge Tests. 3.1 Test programme. ... 3.1 Test programme. The detail and geometry of the tests are tabulated in Table 1.

19 Mar 2010: To test for case-control differences between groups, distributions were firsttested for normality, and generally a Wilcoxon test wasused. ... To test forhip fracture case-control differences, repeated-measuresMANOVA was used with and without age

3 Feb 2004: The engineer can then design the reinforcement in the twodirections, and to be economic, he curtails the reinforcement assoon as possible, so that the resistance moment follows veryclosely the applied moment. ... γ factors as low as about 0.20 arepresent

14 May 2002: Simple equilibriumconsiderations lead to relationships between the tension inthe middle of cord i, Ti, the sag of cord i, si, and the sagof cord i 1, si1, etc. ... This test confirmed a conclusion already reached bySeffen et al. (2000), that an advantage

11 Jul 2007: These relations can be found in and have been verified using published test data in [8]. ... Again, the structure but not the loading is symmetric about the middle support.

3 Aug 2011: Bagi[13] also observed this effect in 2D simulations of a uniaxial compression test, showing data which. ... For example, Head [2] suggests minimumratios of 5, 6, 10 or 12, depending on the nature of the laboratory test.

8 Apr 2011: Double-shear pull tests and single-shear pull tests have been the most popular test methods, as a result of their simplicity (Chen et al., 2001). ... Figure 2 — Direct pull out tests set-ups. (a) Beam test (b) Modified beam test.

31 Aug 2001: Is this because thetechnology is wrong? Are the economics wrong? Are engineers too conservative? ... There will thus need to be research before economic designrules can be introduced.

20 Jul 2004: It is also unlikely that AFRP or CFRP will be economic for flexure. ... Bent pultrusions, however, will never be economic. 4.4 Internal confinement for compression.

11 Jul 2007: Two different yield criteria were considered in Ref [16] both of which approximate observed results from tests on standard monolithic specimens. ... section. Using fc in lieu of Neilsen’s use of the compressive test strength (fcu ) the reinforcement

22 Mar 2002: thickness of the membrane. Values between 1% and100% of the thickness have been used, considering dif-ferent imperfection magnitudes to test the sensitivityof the predicted response. ... Note that all of these modes closely resemble theexpected wrinkled