Search

22 Aug 2001: 2.2 Some remarks about calibration chamber tests. 3 Centrifuge Tests. 3.1 Test programme. ... 3.1 Test programme. The detail and geometry of the tests are tabulated in Table 1.

31 Aug 2001: Is this because thetechnology is wrong? Are the economics wrong? Are engineers too conservative? ... There will thus need to be research before economic designrules can be introduced.

24 Aug 2001: John D McKinley, Cambridge University. Geotechnical Engineering Group. Abstract. Civil Engineers have used grouted ground anchors to transmit tensile loads into the soil because of the technique’s economic and practical ... The calculated values for

9 Nov 2001: models32 etc. The code rules are mostly based on a set of tests. ... Would. such a bridge be economic? It is made from a rectangular block.

17 Apr 2001: The work carried out on this test specimen included the preliminary analysis, its construction and assembly, and a series of tests performed during both the non-composite and the composite stages. ... An advanced three-dimensional finite-element model of

25 May 2001: Every space structure must undergo an extensive ground validation test program to ensure in-orbit reliability and performance in space. ... In order to obtain reliable predictions for the behaviour of a structure in space, it is therefore necessary to

17 Aug 2001: Measurement of Small Strains using Semiconductors in Centrifuge Tests CN. 1.0 Introduction. ... Jama@ 1995 Page 7. Measurement of Small Strains using Semiconductors in Centrifuge Tests CN.

5 Jul 2001: Extensional Stiffness of Tape-Spring. Dead band caused by play in test set-up – now fixed although no results. ... Redesign of hinge based on data. New automated set-up to be used to obtain peak moment and test hinges of different sizes.

17 Aug 2001: This report concerns itself with theperformance of this new actuator under ‘high g’ centrifuge tests. ... using this system on payloads of upto 287 kg in a 80g centrifuge test.

20 Dec 2001: The test was continued until snapping of the spiral occurred. For circular concrete specimens with a single spiral, tests were made at 8 days, 15 days and 28 days to obtain ... CONCLUSIONS Concentric compression tests on short AFRP spirally-confined

29 Aug 2001: from shearvane tests, Hamilton et al (19!31). Assuming identical vertical stresses, overconsolidation. ... of the centrifuge test the fingers came cut of contact with the tower. -.

5 Apr 2001: Deployment. tests carried out on this structure, with two different packaging schemes have confirmed that. ... only for a limited set of test cases it was possible to achieve full convergence.

17 Aug 2001: This report describes the test methods and presents the results of the tests in all threesoil types tested. ... l the usefulness of results obtained in drained penetrometer tests, which fail to show cleartrends compared with undrained penetrometer test

19 Jan 2001: Adhesive-bonded beamsThe goal of the adhesive-bonded tests was to determine the. ... 9). Experimental methodologyThe AFRP tendons were prepared to suit the particular test se-.

21 Mar 2001: 5 Packaging and Deployment Tests 345.1 Zig-Zag Folding. 365.2 Wrapping. 375.3 Folding Machine. ... Figure 4.7: Hub connection between hub and membrane. Chapter 5. Packaging and Deployment Tests.

9 Nov 2001: Material Test=tendon Dead end Live end f cu: MPa. N b3 N b3. ... presented here. This would suggest that a fairly com-. prehensive test programme would need to be carried.

17 Aug 2001: The test. procedures roughly followed the same steps reported by Evans et al. ... open. 2. 3 Sequence of operations during test. Test CBLCl was conducted on Wednesday 21st.

21 Mar 2001: 293.10 Unstressed rib shape. 31. 4.1 Schematic top view of test article. ... 404.9 Schematic layout of tension test on membrane strip. 434.10 Tension tests on membrane strips.

26 Jun 2001: 26 centrifuge tests, 12 triaxial compression tests, and 12 shear box tests were carried out. ... v. ). Keywords: CPT, pile, centrifuge test, sand, slope test, pull-out test, triaxial test, total stress cell, dimensional analysis, numerical analysis,

26 Jun 2001: Tunnel stability in the first test series was well predicted by plasticity theory. ... The test series conducted on model tunnel headings showed the stability to be strongly influenced by the heading geometry.