Search

7 Jul 2005: 2.6%, 6.6%, and 13.3%, were used. 1 Tension, compression, and shear tests were performed on foamsamples of all three densities using a screw-driven Instron 5500R test machine. ... Compression tests using a Celanese test rig were conducted on three

27 Jul 2009: These experiments are now reported. 3 Experimental InvestigationA series of compressive tests was performed on square honey-. ... 3c. A series of compression tests was performed on the macro-scopic sandwich panels.

27 Dec 2017:  .     . out-of-plane, longitudinal shear test. ... on the load-displacement response. Specifically, repeat tests were performed on specimens of.

24 Apr 2006: Test material and experimental procedure. A series of shear collapse experiments has beenconducted on conical frusta. ... Introduction. Shear collapse experiments. Test material and experimental procedure. Measured collapse response in shear.

29 Jan 2014: initial peak load measured in the drop-weight tests exceed those measured under. ... Y-frame sandwich beam in the drop-weight tests. The photographs show the.

29 Oct 2018: Additional details of helium pycnometry. are given in Appendix A. Uniaxial tensile tests were performed using a screw-driven test machine, with the loading direction inclined. ... In-situ. tensile tests were conducted with a micro-test stage equipped

17 Jun 2005: s̄= 0.034 and ā = 0.1. Test geometries are marked on the map. ... Tensile specimens of dog-bone geometry were cut fromaluminium face sheets. The tensile tests were performed in ahydraulic test machine at a strain rate of 10-4 / s; the axial swas

31 Jan 2006: Neglecting this contribution yields an error of<5% over the entire range of test conditions. ... Since the core crushing velocity inthe beam tests is roughly constant at prescribed impulse (Fig.

14 Aug 2023: In such. indentation tests, an indentation tip is lowered onto the surface of the test specimen and. ... modulus and hardness obtained from indentation tests are plotted against the size of the.

10 Aug 2009: Consequently, the face-sheets of the Y-frame sandwich could slide past eachother during the uniaxial compression test. ... A pair of specimens was usedin each double-lap shear test, again using the apparatussketched in Fig.

4 Nov 2013: 5.3 Beam Tests Tests performed on beams in 3-point bending have been designed to probe failure by core shear and face yielding. ... All other results used in this article refer to tests performed in this range.

6 Oct 2004: test performed. Scissor tear tests maintain a sharp crack tip and give a low toughnessvalue of 2.5 kJ m2 for human skin. ... Consequently, the toughnessvalues from trouser-tear tests are used to compare the penetration experiments withthe model

1 Sep 2023: below. The pillar compression tests of Xu et al. (2017) found that the yield. ... of 0.05 s1 in the indentation test. In consistent manner, Herbert et al.

7 Jul 2004: independent shear testdata (from a double lap shear test, with foam of thickness 20mm). ... A.3) that the yield surface can beestimated by simply measuring in a uniaxial test.

1 May 2019: used in the follow-on study at elevated temperature.). 2.2. Test method. ... labelled Test I) of relative density ρ 0.11 is shown in Fig.

2 Aug 2012: We test this hypothesis by comparing the indentationdisplacement dI with the total displacement d at the peak load, asfollows. ... equal to thosemeasured in the three-point bend tests on the clamped andsimply supported beams.

23 May 2005: 1. 4. Experimental results and comparison with theory. 4.1. Direct impact tests. ... Direct impact tests. Normal impact of a free mass. Experimental results and comparison with theory.

19 Dec 2008: 2.4 Dynamic Test Protocol. The dynamic out-of-plane com-ressive response of the square honeycombs was measured from aeries of direct impact tests in which the forces on the ... Fig. 5 Stress versus time history measured in the Kolsky barduring a

29 May 2019: hydraulic test machine at a nominal strain rate of ε̇ = 4 104 s1. ... The tests were conducted at 100 C in a. temperature-controlled chamber with a glass window for in-situ observation of the specimen during the test.

10 Aug 2009: 2a and b, respectively. These compression tests were conducted on 6 mm 6 mm 6 mm cuboidal specimens in ascrew-driven test machine with the specimens compressed between lubricated flat platens. ... A select number of repeat tests were conducted for each