Search

10 Aug 2009: Consequently, the face-sheets of the Y-frame sandwich could slide past eachother during the uniaxial compression test. ... A pair of specimens was usedin each double-lap shear test, again using the apparatussketched in Fig.

31 Jan 2006: Neglecting this contribution yields an error of<5% over the entire range of test conditions. ... Since the core crushing velocity inthe beam tests is roughly constant at prescribed impulse (Fig.

1 Sep 2023: below. The pillar compression tests of Xu et al. (2017) found that the yield. ... of 0.05 s1 in the indentation test. In consistent manner, Herbert et al.

4 Nov 2013: 5.3 Beam Tests Tests performed on beams in 3-point bending have been designed to probe failure by core shear and face yielding. ... All other results used in this article refer to tests performed in this range.

6 Oct 2004: test performed. Scissor tear tests maintain a sharp crack tip and give a low toughnessvalue of 2.5 kJ m2 for human skin. ... Consequently, the toughnessvalues from trouser-tear tests are used to compare the penetration experiments withthe model

1 May 2019: used in the follow-on study at elevated temperature.). 2.2. Test method. ... labelled Test I) of relative density ρ 0.11 is shown in Fig.

7 Jul 2004: independent shear testdata (from a double lap shear test, with foam of thickness 20mm). ... A.3) that the yield surface can beestimated by simply measuring in a uniaxial test.

2 Aug 2012: We test this hypothesis by comparing the indentationdisplacement dI with the total displacement d at the peak load, asfollows. ... equal to thosemeasured in the three-point bend tests on the clamped andsimply supported beams.

19 Dec 2008: 2.4 Dynamic Test Protocol. The dynamic out-of-plane com-ressive response of the square honeycombs was measured from aeries of direct impact tests in which the forces on the ... Fig. 5 Stress versus time history measured in the Kolsky barduring a

10 Aug 2009: 2a and b, respectively. These compression tests were conducted on 6 mm 6 mm 6 mm cuboidal specimens in ascrew-driven test machine with the specimens compressed between lubricated flat platens. ... A select number of repeat tests were conducted for each

29 May 2019: hydraulic test machine at a nominal strain rate of ε̇ = 4 104 s1. ... The tests were conducted at 100 C in a. temperature-controlled chamber with a glass window for in-situ observation of the specimen during the test.

23 May 2005: 1. 4. Experimental results and comparison with theory. 4.1. Direct impact tests. ... Direct impact tests. Normal impact of a free mass. Experimental results and comparison with theory.

3 Oct 2020: nanocomposites. Single edge notch bend tests are conducted to relate the fracture toughness. ... uniaxial compression tests of the solid and cellular nanocomposites. The solid PMMA is.

29 May 2013: 2a. The tensile tests were conducted in a screw driven test machine at a nominal applied strain rate of 103 s1 with the nominal stress determined from the test machine load ... In most cases, failure/penetration of the plates was clearly seen after

1 Jul 2004: These predictions are compared to exmental results obtained from triaxial tests on an aggregate of s. ... de-af-. ansti-. is. computed by means oftrue triaxial tests, wherein the three prin-cipal stresses depicted in Fig.

7 Jul 2004: The 6-noded triangle with one-point reduced integration fails both the single element test and the patch test (it passes both tests for plane strain defor- mation). ... and Zdunek, A. B. (1989) A theoretical study of the Brine1 hardness test.

6 Jul 2005: 1. Uniaxial compression testsUniaxial compression tests were performed using a standard screw driven test. ... Repeated uniaxial and hydrostatic tests showed that the stressversus strain curves of Fig.

2 Aug 2012: The mass distribution ofthe test geometries is indicated for two choices of areal mass. ... 3. 3 Experimental Results. The three-point bending tests were conducted using a 100kN screw driven test machine with a constant cross-headvelocity of _d5103 mm/s.

4 Oct 2008: Post-test photographs of the h = 0.25 mm copperplates are shown in Figure 3. ... 2.2. Specimen configuration. 2.3. Test protocol. 2.4. Material properties. 3. Summary of experimental findings.

15 Feb 2006: 22 mm. These lengths correspond to the two core thicknesses employed in the sandwich tests. ... Test protocol. Experimental results. Finite element simulations. Constitutive description. Comparison of finite element predictions and measurements.