Search

1 May 2019: Aspects of theresearch roadmap in application scenarios. Federal Ministry for Economic Affairsand Energy, Tech. ... A novel methodology for the design of waste heat recovery networkin eco-industrial park using techno-economic analysis and multi-objective

1 May 2019: The cause of the observed discrepancy is unclear. A number of sensitivity studies wereperformed to test how the fall-effect is influenced by the model parameters. ... This infor-mation would help to test the accuracy of the employed methods in the case

1 May 2019: 26] were used to test the model. This studyemployed a screw configuration consisting of a conveying section followed by a section ofconveying/kneading elements and then an additional conveying section. ... 4] (which used the same experimental test case

1 May 2019: The purpose of this paper is to present an attempt atmodelling these PSDs and test the sensitivity of soot PSDs with respect to processesand parameters in the soot model.

1 May 2019: 17. of 4.5. The properties of a test fluid were chosen in units such that the coagulationconstant was given by K0 = 1 and the inflowing particles were mono-dispersed witha ... Once again, the properties of a test fluid were chosen in units such that the

1 May 2019: In our test it was observed that by varyingthe effective compression ratio in the model, the pressure profile did not match theexperimental data as well as when the crevice model was

13 Sep 2019: The de-tails of the mobility size measurements and the dilution tests have been given elsewhere[31]. ... This is consistent with the numerical sensitivity tests performed byLindberg et al.

1 May 2019: The concept represents a performance mea-sure for the evaluation. Evaluation in the perspective of economics and environment areconsidered at current stage. ... Product Product denotes for an economic goods or service. 4.2 Ontological representation of

1 May 2019: Lindrooth. Eco-industrialparks: a case study and analysis of economic, environmental, technical and regu-latory issues.

1 May 2019: out over this range with and without the correlation for unavailable sites, to test itsimportance in the experimental size range. ... 4. Test collision if the second aggregate were moved along the z-axis towards theorigin.

1 May 2019: Yes. Prof Markus Kraftmk306@cam.ac.uk. Applying the model. • test model against experimental data. •

1 May 2019: Next the timing of injection was varied as a blind test of the model, results are presentedin Figure 2a.

1 May 2019: We test the methodsby determining the influence of the observations on estimates of some Arrhenius pre-exponential factors in the kinetic mechanism used to model the data.

1 May 2019: Experimental data for validation of the combustion models was collected from a Caterpil-lar multi-cylinder test engine (MCTE). ... Finally, the conclusions are drawn at the end. ENGINE SET-UP. Experimental data for validation of the combustion models was

1 May 2019: During the tests, in–cylinder pressure was recorded with a piezoelec-tric pressure transducer (KISTLER, 6052A) at every 0.16 Crank Angle Degree (CAD)and ensemble–averaged over 130 engine cycles.

1 May 2019: 3.1 Numerical parameters. The numerical convergence of the algorithm was investigated by solving a test systemwith different numerical parameters such as:. ... ii) Number of runs (L);. (iii) Splitting time-step (ts). The test system is described below.

1 May 2019: 2 Experimental setup. 2.1 Engine Configuration. The experimental data used in this study is from a Caterpillar multi-cylinder test engine(MCTE) and is the same as the data used

1 May 2019: 4.2 Drying a Droplet Containing Colloidal Silica. The first test case simulated is the drying of a colloidal silica droplet containing 16nmparticles suspended in water at an initial mass fraction

1 May 2019: 5.1 Drying a Droplet of Detergent Slurry. The first test case is the simulation of a droplet of detergent slurry drying.

1 May 2019: Numerical tests of theaccuracy of the interpolative closure are contained in [12] for inorganic and in [41]for organic nanoparticles. ... All these methods are com-pared by Vanni [115] for a comprehensive set of test cases.