Search
Search Funnelback University
- Refined by:
- Date: 2004
Did you mean economiespast |u:www-mech.eng.cam.ac.uk?
1 -
10 of
33
search results for Economics test |u:www-mech.eng.cam.ac.uk
where 0
match all words and 33
match some words.
Results that match 1 of 2 words
-
PII: S1359-6462(00)00519-4
www-mech.eng.cam.ac.uk/profiles/fleck/papers/130.pdf7 Jul 2004: Figure 1 showsa schematic of the indentation test set-ups. Cyclic indentation tests were also performed in load control at a test frequency of 20Hz and at a loadratio R 5 ... The maximum and minimum values of the load and the displacement, and the number -
PII: S1359-6454(01)00058-1
www-mech.eng.cam.ac.uk/profiles/fleck/papers/135.pdf7 Jul 2004: Fig. 3. Sketch of the loading rig for the biaxial and hydrostatictension tests. ... A comparison between the “Arcan”and double-lap shear stress versus strain curves forthe H100 foam shows that while the shear strengthsfrom both tests are in -
PII: S0142-1123(01)00010-X
www-mech.eng.cam.ac.uk/profiles/fleck/papers/137.pdf7 Jul 2004: The details are the same as forthe K-decreasing tests, but withc=0. ... Fig. 3. Comparison of da/dN from K-increasing,K-decreasing andK-constant tests. Tests were performed atR=0.1 on compact tensionspecimens of Alulight foam, of composition -
PII: S1359-6454(99)00128-7
www-mech.eng.cam.ac.uk/profiles/fleck/papers/103.pdf7 Jul 2004: loading platens. To overcome this, subsequent com-. pression tests were conducted using the dogbone. ... 4; the in-. itial modulus is the same as in the tensile tests. -
doi:10.1016/j.compositesa.2004.10.024
www-mech.eng.cam.ac.uk/profiles/fleck/papers/187.pdf9 Dec 2004: 318. 319. 320. 321. 322. 323. 324. 325. RREC2.1.2. Test procedureDirect compression tests were carried out using theCelanese compression rig. ... uniaxial test specimens. The overall geometry of these. plates is shown in Fig. -
PII: S0921-5093(00)00954-0
www-mech.eng.cam.ac.uk/profiles/fleck/papers/122.pdf7 Jul 2004: A similarresponse has been observed previously [13] in deepnotch compression tests on the Alporas foam. ... TTAlcan 65T 89L 95. Alporas 84L, T and TT. 6. Fracture toughness tests. -
PII: S0020-7683(02)00250-0
www-mech.eng.cam.ac.uk/profiles/fleck/papers/145.pdf7 Jul 2004: 7a). The maximum load and the stiffness measured in each test aresummarized on Table 3. ... the imperfection causes a marked reduction in the stiffness.Images taken during the test (Fig. -
PII: S1359-6454(99)00097-X
www-mech.eng.cam.ac.uk/profiles/fleck/papers/108.pdf7 Jul 2004: fatigue tests: at the end of the fatigue test, when the. ... The specimen was then re-loaded and. the test was resumed. In the fatigue tests theunloading modulus was calculated from the changein axial strain upon reducing the applied stress. -
PII: S0142-1123(01)00012-3
www-mech.eng.cam.ac.uk/profiles/fleck/papers/131.pdf7 Jul 2004: 3] for mono-tonic shear: fatigue tests were performed at 20 Hz on. ... 7.Repeat tests confirmed that the scatter in stress–strainresponse was negligible for face sheets of any giventhickness. -
doi:10.1016/j.compositesa.2004.03.006
www-mech.eng.cam.ac.uk/profiles/fleck/papers/161.pdf21 Sep 2004: delamination fracture tests, especially those featuring high-. resolution measurements of crack displacements and. ... to seat the specimen halves in the loading jig. 3.2. Shear tests.
Search history
Recently clicked results
Recently clicked results
Your click history is empty.
Recent searches
Recent searches
Your search history is empty.